精密電熱恒溫干燥箱工作溫度為300℃(需特種高溫可定做),可供各種試品置入使用。箱體由簿鋼板制成,箱體內有一供放置試品的工作室,工作室內有試品擱板,試品可置于其上進行干燥,如遇試品較大,可抽去擱板,工作室與箱體外殼間有相當厚度的保溫層中以硅棉或珍珠巖作保溫材料,箱門間有一玻璃門或觀察口,以供觀察工作內之情況。電熱器裝于箱體內工作室下,共分二組,即“高溫和低溫”,并有指示燈指示,綠燈亮表示電熱器工作,箱內在加熱,紅燈滅表示加熱停止。
精密電熱恒溫干燥箱是現代廣泛應用于生物化學、化工制藥、醫療衛生、農業科研、環境保護等研究應用領域,且智能化程度比較高的一款儀器設備產品,它基本定時功能,也就是說工作人員只需要定好時間,然后其他的操作就不再需要人來完成了,此時數控電熱恒溫鼓風干燥箱會(huì )根據定好的時間來進行自動運作,大大提高了樣品干燥過程中的自動化程度。
從參數上來看,數控電熱恒溫鼓風干燥箱的定時范圍是1-9999分鐘,也就是基本上是一個星期沒問題,因此數控電熱恒溫鼓風干燥箱的定時范圍是比較大的,這也表明該設備能夠長時間連續運行,而且當用戶剛買到數控電熱恒溫鼓風干燥箱的時候會(huì )發現,由于新機的智能儀表默認是常開的,因此在不需要定時的情況下,基本上是可以無時間限制工作的。
精密電熱恒溫干燥箱安裝與使用:
1、打開包裝,按照說明書裝箱單檢查附件足否齊全。
2、把箱體放在室內于燥的地面或平臺上,必須安裝地線。
3、使用電源必須與箱體用電源相符,并在電源連接處安裝保險裝璧。
4、接通電源,打開各功能開關,指針式控溫儀表轉動溫度設定旋鈕,設定所須要的溫度。(數顯式控溫詳看數顯儀表操作說明)。
5、工作中應適當打開排氣閥,使箱內氣體流通及潮氣外溢,初次使用時必須進行烘干,加熱至1509左右待箱內煙霧排毋時再進行使用。
6、初次恒溫過程中,因受熱沖擊值的影響,可能出現溫沖過高現象,待溫度降到恒溫點,再次恒溫時,其溫沖現象就會(huì )降低,反復幾次恒溫后,即達到技術耍求。
7、在使用過程中應隨時注意其溫度變化,如超溫過大應及時關掉電源進行檢查。